Warning

This is the dev documentation for an unreleased version of MPF!

This is the documentation for MPF 0.56, which is the “dev” (next) release of MPF that is a work-in-progress. Unless you’re specifically looking for this version, you probably want to use the version of documentation called “latest” which is for the latest released version of MPF. That documentation is at docs.missionpinball.org/en/latest.

snux:

Config file section

Valid in machine config files YES
Valid in mode config files NO

The snux: section of your config is where you configure the snux platform.

This is an example:

hardware:
  platform: virtual    # use your platform here
  driverboards: wpc
  coils: snux
  switches: snux
system11:
  ac_relay_delay_ms: 75
  ac_relay_driver: c_ac_relay
snux:
  diag_led_driver: c_diag_led_driver
coils:
  c_diag_led_driver:
    number: c24
    default_hold_power: 1.0
  c_flipper_enable_driver:
    number: c23
    default_hold_power: 1.0
  c_ac_relay:
    number: c25
    default_hold_power: 1.0
  c_side_a1:
    number: c11a
  c_side_a2:
    number: c12a
    default_hold_power: 0.5
  c_side_c1:
    number: c11c
  c_side_c2:
    number: c12c
    default_hold_power: 0.5
  c_flipper_left_main:
    number: FLLM
  c_flipper_left_hold:
    number: FLLH
    allow_enable: true

switches:
  s_flipper_left:
    number: sf01
  s_test:
    number: s77

flippers:
  f_test_single:
    main_coil: c_flipper_left_main
    hold_coil: c_flipper_left_hold
    activation_switch: s_flipper_left
This example is tested to be valid MPF config. However, it is not integration tested.
hardware:
  platform: virtual    # use your platform here
  driverboards: wpc
  coils: snux
  switches: snux
system11:
  ac_relay_delay_ms: 75
  ac_relay_driver: c_ac_relay
snux:
  diag_led_driver: c_diag_led_driver
coils:
  c_diag_led_driver:
    number: c24
    default_hold_power: 1.0
  c_flipper_enable_driver:
    number: c23
    default_hold_power: 1.0
  c_ac_relay:
    number: c25
    default_hold_power: 1.0
  c_side_a1:
    number: c11a
  c_side_a2:
    number: c12a
    default_hold_power: 0.5
  c_side_c1:
    number: c11c
  c_side_c2:
    number: c12c
    default_hold_power: 0.5
  c_flipper_left_main:
    number: FLLM
  c_flipper_left_hold:
    number: FLLH
    allow_enable: true

switches:
  s_flipper_left:
    number: sf01
  s_test:
    number: s77

flippers:
  f_test_single:
    main_coil: c_flipper_left_main
    hold_coil: c_flipper_left_hold
    activation_switch: s_flipper_left

Required settings

The following sections are required in the snux: section of your config:

diag_led_driver:

Single value, type: string name of a coils device. Defaults to empty.

The coil to use to drive the diag LED on the snux board. This is usually driver 23 on the Snux board.

Optional settings

The following sections are optional in the snux: section of your config. (If you don’t include them, the default will be used).

console_log:

Single value, type: one of the following options: none, basic, full. Default: none

Log level for the console log for this platform.

file_log:

Single value, type: one of the following options: none, basic, full. Default: basic

Log level for the file log for this platform.